Classic rims

4 aluminum rims Ø 10 mm - CPC production
4 aluminum rims Ø 10 mm - CPC production
Aluminum rims for miniature cars machined in bar turning Outside ø: 10 mm Inside ø: 4.50 mm (Diameter of insert or rivet) < p> ø of the hole: 2 mm Thickness: 2.70 mm (7.00 mm with the scope) Depth: 0.70 mm
€1.90
4 rims Ø8.50 mm - Aluminum - CPC Production
4 rims Ø8.50 mm - Aluminum - CPC Production
4 aluminum rims produced by CPC Production Outside ø: 8.50 mm Inside ø (at the bottom, for the insert): 3.80 mm Thickness: 3.80 mm Depth: 2.20 mm ø of the hole for the axle: 2 mm
€1.90
4 aluminum rims Ø10.50 mm x 5.80 mm - CPC
4 aluminum rims Ø10.50 mm x 5.80 mm - CPC
Aluminum rims for model cars A = Ø 10.50 MM B = Ø 9.50 MM C = Ø 2.00 MM < p> D = Ø 4.50 MM E = Ø 2.00 MM F = Length: 5.80 MM Depth: 3.50 mm Material: Aluminum Turned parts
€1.50
Aluminum wheels Ø8.80 mm (lot of 5)
Aluminum wheels Ø8.80 mm (lot of 5)
Aluminum rims for miniature cars A = Ø 8.80 MM B = Ø 6.50 MM C = Ø 2.00 MM D = Ø 4.10 MM E = Ø 2.00 MM F = Length: 5 MM Material: Aluminum Parts tours
€1.50
10 aluminum wheels Ø11.20mm x 7.60 mm
10 aluminum wheels Ø11.20mm x 7.60 mm
Destocking of classic rims for 1/43 miniatures - This is an end of stock that will not be renewed Corresponds to a 19 inch rim (Scale 1/1) p> Outside Ø: 11.20 mm Inside Ø: 8mm at the bottom of the rim Total depth: 3mm Rim thickness without reach at the rear: 7 mm Designed for a Ø2 mm wheel axle
€5.00
4 brass rims + nickellage Ø10 - CPC production
4 brass rims + nickellage Ø10 - CPC production
Brass rims produced by turning with a surface treatment: Nickle plating Outer ø: 10 mm Inner ø: 9 mm (ø maxi for the insert) p> Depth: 1.60 mm (Maximum depth for the insert) Width: 5 mm (Width for the tire) Total width: 6 mm ø of the hole for the axis: 2 mm
€2.50
4 rims Ø10.20 x 10.50 mm - brass - CPC Production
4 rims Ø10.20 x 10.50 mm - brass - CPC Production
Turned brass rims Outer ø: 10.20 mm Inner ø: From top to bottom: 9.60 mm - 8.80 mm - 7.80mm ø hole diameter: 1.50 mm Length: With rear reach: 10.50 mm - Without rear reach: 9.50 mm
€4.50
4 rims Ø12.50 mm - Aluminum - CPC Production
4 rims Ø12.50 mm - Aluminum - CPC Production
Aluminum rims produced by turning Outer ø: 12.50 mm Outer ø in the center: 10.60 mm Inner ø: 9.20 mm at the bottom - 11 mm at the top Thickness: 5 mm Total thickness: 6 mm ø of the hole for the axis: 2 mm
€3.00
4 jantes ø10.50 X7 mm - Aliminium - CPC Production
4 jantes ø10.50 X7 mm - Aliminium - CPC Production
Jantes en aluminium avec avancée centrale permettant de laisser un espace entre l'insert et le fond de la jante donnant un aspect de profondeur (Idéal pour roues à rayon ou à bâton) 

ø extérieur : 10.50 mm
ø intérieur : Fond ø8.30 mm 
ø intérieur buté ø9.30 mm
Profondeur : 4.70 mm -
Profondeur au ø9.30 = 2 mm 
Profondeur sur le centre : 3 mm
Épaisseur : 7 mm

€2.50
4 jantes ø10.50 mm - Laiton - CPC Production
4 jantes ø10.50 mm - Laiton - CPC Production
Déstockage de jantes en laiton. Vendu en l'état
Défaut et bavure  sur le perçage au centre
ø extérieur : 10.50 mm
Épaisseur : 6 mm (6.25 mm avec la portée)
ø intérieur : 7.60 mm
Profondeur : 3.80 mm
Perçage pour l'axe : ø 2 mm
€1.50